J. For. Sci., 2025, 71(2):72-85 | DOI: 10.17221/64/2024-JFS

Analysis of selected functional parameters of saw chainsOriginal Paper

Pavel Nevrkla, Luboš Staněk ORCID..., Jindřich Neruda ORCID...
Department of Engineering, Faculty of Forestry and Wood Technology, Mendel University in Brno, Brno, Czech Republic

Results obtained from the research study focused on the functional parameters of five saw chains tested on a test bench equipped with an electrically driven chain saw brought a number of findings. One of the most important of them is the significant difference between the cutting rates of round and square chains. The cutting rate of square chains R = 27.9 cm2·s–1 is about 12% higher than the cutting rate of round chains. The influence of the chain construction on the chain cutting rate was conclusively demonstrated – the cutting rate of chains with a square profile is higher than the cutting rate of round-profile chains. It was further found out that although the specific energy Em = 77.8 Ws·cm–2 is by ca. 7% lower in the square chain than in the round chain, Student's t-test did not reveal any statistically significant difference in the data on the specific energy consumption of round and square chains, i.e. the influence of the chain design on the specific energy consumption of the chain at cutting was not clearly demonstrated. Other findings, for example, showed that working with a loose saw chain on the guide bar impairs parameters of the chain operation or that energy demands of cutting with the saw chain are directly proportional to wood density (hardness) and increase with the decreasing wood moisture. Yet another finding was learning the energy flow structure, which indicated that 46% of total power input is consumed by the electric motor alone for its operation while only about 7% goes for driving the chain movement along the bar (without cutting) and power input required for cutting is approximately 46%.

Keywords: chainsaw; cutting rate; energy consumption; power saw; structural arrangement

Received: August 21, 2024; Revised: November 15, 2024; Accepted: December 4, 2024; Prepublished online: February 18, 2025; Published: February 24, 2025  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Nevrkla P, Staněk L, Neruda J. Analysis of selected functional parameters of saw chains. J. For. Sci. 2025;71(2):72-85. doi: 10.17221/64/2024-JFS.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Botwin J., Botwin M. (1979): Maszynoznawstwo leśne. Warszawa, PWRiL: 490. (in Polish)
    2. Chuchala D., Orlowski K.A., Sandak A., Sandak J., Pauliny D., Barański J. (2014): The effect of wood provenance and density on cutting forces while sawing Scots pine (Pinus sylvestris L.). BioResources, 9: 5349-5361. Go to original source...
    3. Coutermarsh B.A. (1989): Factors Affecting Rates of Ice Cutting with a Chain Saw. Hanover, US Army Corps of Engineers, Cold Regions Research and Engineering Laboratory: 14.
    4. Cristóvão L., Broman O., Grönlund A., Ekevad M., Sitoe R. (2012): Main cutting force models for two species of tropical wood. Wood Material Science and Engineering, 7: 143-149. Go to original source...
    5. Dąbrowski A. (2012): Reducing kickback of portable combustion chain saws and related injury risks: Laboratory tests and deductions. International Journal of Occupational Safety and Ergonomics, 18: 399-417. Go to original source... Go to PubMed...
    6. Gendek A. (2005): The influence of clutch parameters on the wood cutting efficiency with a chainsaw. [Ph.D. Thesis.] Warsaw, Warsaw University of Life Sciences-SGGW.
    7. Górski J. (1996): Analiza wpływu podstawowych czynników na wydajność i energochłonność procesu skrawania drewna piłą łańcuchową żłobikową. [Ph.D. Thesis.] Warsaw, Wydział Technologii Drewna, SGGW. (in Polish)
    8. Heinzelmann G., Liebhard G., Rosskamp H. (2011): Energy efficient drive train for a high-performance battery chain saw. In: Proceedings of the 1st International Electric Drives Production Conference, Nuremberg, Sept 27-30, 2011: 101-106. Go to original source...
    9. Kaczmarek J. (1971): The Basics of Turning, Abrasive, and Erosive Machining. Warsaw, WNT: 848.
    10. Koch P. (1964): Wood Machining Processes. New York, Ronald Press: 530.
    11. Kováč J., Krilek J., Kučera M., Kopecký Z., Hlásková L. (2013): Ergonomic Process Parameters Cutting Wood. Brno, Mendel University in Brno: 68.
    12. Kozłowski R. (2003): Wpływ typu piły łańcuchowej i gatunku drewna na wydajność skrawania i zużycie paliwa. Przegląd Techniki Rolniczej i Leśnej, 4: 19-21. (in Polish)
    13. Kretschmann D.E. (2010): Mechanical properties of wood. In: Ross R.J. (ed): Wood Handbook: Wood as an Engineering Material. Madison, USDA Forest Products Laboratory: 1-46.
    14. Kuvik T., Krilek J., Kováč J., Štefánek M., Dvořák J. (2017): Impact of the selected factors on the cutting force when using a chainsaw. Wood Research, 62: 807-814.
    15. Kuvik T., Krilek J., Kováč J., Melicherčík J. (2021): Impact of cutting speed and feed rate for cross cutting with saw chains. BioResources, 16: 5341-5349. Go to original source...
    16. Maciak A. (2001): Wpływ parametrów konstrukcyjnych ogniw tnących piły ogniw tnących piły łańcuchowej żłobikowej na wydajność skrawania drewna. [Ph.D. Thesis.] Warsaw, MS, SGGW. (in Polish)
    17. Maciak A. (2007): Wpływ stopnia zanieczyszczenia filtra powietrza pilarki spalinowej na charakterystykę zewnętrzną silnika. Technika Rolnicza, Ogrodnicza, Leśna, 1: 46-48. (in Polish)
    18. Maciak A. (2013): Wpływ czynników konstrukcyjnych i eksploatacyjnych na przebieg procesu i wydajność skrawania drewna pilarką spalinową. Warsaw, Wydawnictwo SGGW: 122. (in Polish)
    19. Maciak A. (2015a): The impact of initial tension on rapidity of dulling of saw cutting chains during cross-cutting of pine wood. Annals of Warsaw University of Life Sciences, 66: 89-98.
    20. Maciak A. (2015b): Impact of the feed force on discontinuity of wood cutting with petrol chainsaw. Annals of Warsaw University of Life Sciences, 66: 99-110.
    21. Maciak A., Kubuśka M. (2018): The influence of initial tension on blunting of chain saw blades and cutting efficiency. Lesne Prace Badawcze, 79: 261-268. Go to original source...
    22. Maciak A., Kubuśka M., Młodzińska E. (2017): Impact of saw chain cutters type on cutting efficiency and fuel consumption in timber cutting. Annals of Warsaw University of Life Sciences, 69: 71-77. Go to original source...
    23. Maciak A., Kubuśka M., Moskalik T. (2018): Instantaneous cutting force variability in chainsaws. Forests, 9: 660. Go to original source...
    24. Marchal R., Mothe F., Denaud L., Thibaut B., Bleron L. (2009): Cutting forces in wood machining - Basics and applications in industrial processes. A review. Holzforschung, 63: 157-167. Go to original source...
    25. Mikleš M., Tkáč Z., Jablonický J., Hujo L., Mikleš J., Krilek J. (2011): Lesnícke stroje a zariadenia. Zvolen, Technical University in Zvolen: 290. (in Slovak)
    26. Neruda J., Nevrkla P., Cach A. (2022): Práce s motorovou pilou a křovinořezem. Brno, Mendel University in Brno: 137. (in Czech)
    27. Obliwin W.N., Sokolow A.M., Liejtas M. (1988): Ergonomics in the Forest Supply Industry. Moscow, Izdatielstwo Liesnaja Promyszliennost: 224.
    28. Otto A., Parmigiani J. (2015): Velocity, depth-of-cut, and physical property effects on saw chain cutting. BioResources, 10: 7273-7291. Go to original source...
    29. Poje A., Mihelič M. (2020): Influence of chain sharpness, tension adjustment and type of electric chainsaw on energy consumption and cross-cutting time. Forests, 11: 1017. Go to original source...
    30. Reynolds D.D., Soedel W., Eckelman C. (1970): Cutting characteristics and power requirements of chain saws. Forest Products Journal, 20: 28-34.
    31. Sowa J.M. (1989): Wpływ czynników techniczno-technologicznych na poziom drgań mechanicznych pilarek spalinowych. Zeszyty Naukowe Akademii Rolniczej w Krakowie, Leśnictwo, 23: 183-191. (in Polish)
    32. Stempski W., Grodecki J. (1998): Wpływ kąta zaostrzenia ogniw tnących na wydajność skrawania i trwałość pił łańcuchowych. Poznańskie Towarzystwo Przyjaciół Nauk. Prace Komisji Nauk Rolniczych i Leśnych, 86: 73-82. (in Polish)
    33. Štollmann V., Slugeň J. (2009): Lesnícke mechanizačné prostriedky. Zvolen, Technical University in Zvolen: 198. (in Slovak)
    34. Trzeciak P. (2003): Wpływ napięcia i intensywności smarowania piły na wydajność skrawania drewna pilarką. [MSc. Thesis.] Warszawa, SGGW. (in Polish)
    35. Więsik J. (1994): Model symulacyjny procesu skrawania drewna piłą łańcuchową. Przegląd Techniki Rolniczej i Leśnej, 10: 17-19. (in Polish)
    36. Wojtkowiak R. (2004): Ekologiczne i eksploatacyjne aspekty stosowania w lasach środków smarnych mineralnych i roślinnych w układach tnących pilarek łańcuchowych. Roczniki Akademii Rolniczej w Poznaniu. Rozprawy Naukowe, 350: 1-151. (in Polish)
    37. Wyeth D.J., Goli G., Atkins A.G. (2009): Fracture toughness, chip types and the mechanics of cutting wood. A review. Holzforschung, 63: 168-180. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content