J. For. Sci., 2016, 62(1):8-16 | DOI: 10.17221/120/2014-JFS

Objective and subjective assessment of selected factors of the work environment of forest harvesters and forwardersOriginal Paper

M. Jankovský, V. Messingerová, M. Ferenčík, M. Allman
Department of Forest Harvesting Logistics and Ameliorations, Faculty of Forestry, Technical University in Zvolen, Zvolen, Slovak Republic

This article was aimed at assessment of selected factors of the work environment, which influenced the operators of harvesters and forwarders. The selection of the work environment factors was based on a thorough literature survey. From the survey exposure to whole-body vibrations, noise (equivalent and peak), microclimatic conditions and mental load were selected for detailed observations. The measurements were conducted according to international standards and assessed according to European or national legislation. Subjective assessment of the effects of the work environment was conducted through a structured interview. The exposure to whole-body vibrations was 0.5 m.s-2. The equivalent noise exposure was 78 dB, peak noise exposure was 130 dB. The average temperature inside the machine cabs was 17.9°C and average airflow velocity was 0.06 m.s-2. Mental load was high according to the Meister questionnaire, three operators considered the load inadequate, two considered it adequate. Subjective assessment showed that operators considered other factors to be light or no load

Keywords: noise exposure; whole-body vibrations; microclimate; mental load

Published: January 31, 2016  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Jankovský M, Messingerová V, Ferenčík M, Allman M. Objective and subjective assessment of selected factors of the work environment of forest harvesters and forwarders. J. For. Sci. 2016;62(1):8-16. doi: 10.17221/120/2014-JFS.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Alahmer A., Mayyas A., Omar M., Shan D. (2011): Vehicular thermal comfort models; a comprehensive review. Applied Thermal Engineering, 31: 995-1002. Go to original source...
    2. Ala-Mursula L., Vahtera J., Kivimäki M. (2004): Effect of employee worktime control on health: prospective cohort study. Occupational and Environmental Medicine, 61: 239-246. Go to original source... Go to PubMed...
    3. Allen T.D., Herst D.E.L., Bruck C.S., Sutton M. (2000): Consequences associated with work-to-family conflict: a review and agenda for future research. Journal of Occupational Health Psychology, 5: 278-308. Go to original source... Go to PubMed...
    4. Andreoni G., Santambrogio G.C., Rabuffetti M., Pedotti A. (2002): Method for the analysis of posture and interface pressure of car drivers. Applied Ergonomics, 33: 511-522. Go to original source... Go to PubMed...
    5. Axelsson S.Å., Pontén B. (1990): New ergonomic problems in mechanized logging operations. International Journal of Industrial Ergonomics, 5: 267-273. Go to original source...
    6. Axelsson S. (1998): The mechanization of logging operations in sweden and its effect on occupational safety and health. International Journal of Forest Engineering, 9: 25-31. Go to original source...
    7. Aybek A., Kamer H. A., Arslan S. (2010): Personal noise exposures of operators of agricultural tractors. Applied Ergonomics, 41: 274-281. Go to original source... Go to PubMed...
    8. Beuk D., Tomašić Ž., Horvat D. (2007): Status and development of forest harvesting mechanisation in Croatian state forestry. Croatian Journal of Forest Engineering, 28: 63-82.
    9. Bilski B. (2013): Exposure to audible and infrasonic noise by modern agricultural tractors operators. Applied Ergonomics, 44: 210-214. Go to original source... Go to PubMed...
    10. Boileau P.E., Rakheja S. (1990): Vibration attenuation performance of suspension seats for off-road forestry vehicles. International Journal of Industrial Ergonomics, 5: 275-291. Go to original source...
    11. Burdorf A., Swuste P. (1993): The effect of seat suspension on exposure to whole body vibration of professional drivers. Annals of Occupational Hygiene, 37: 45-55. Go to PubMed...
    12. Cengiz T.G., Babalik F.C. (2007): An on-the-road experiment into the thermal comfort of car seats. Applied Ergonomics, 38: 337-47. Go to original source... Go to PubMed...
    13. Deprez K., Moshou D., Anthonis J., De Baerdemaeker J., Ramon H. (2005): Improvement of vibrational comfort on agricultural vehicles by passive and semi-active cabin suspensions. Computers and Electronics in Agriculture, 49: 431-440. Go to original source...
    14. Dupuis H., Zerlett G. (1986). The Effects of Whole-body Vibration. New York, Springer: 162. Go to original source...
    15. Farzaneh Y., Tootoonchi A. (2008): Controlling automobile thermal comfort using optimized fuzzy controller. Applied Thermal Engineering, 28: 1906-1917. Go to original source...
    16. Fernández M.D., Quintana S., Chavarría N., Ballesteros J. (2009): Noise exposure of workers of the construction sector. Applied Acoustics, 70: 753-760. Go to original source...
    17. Gao N., Niu J. (2004): CFD study on micro-environment around human body and personalized ventilation. Building and Environment, 39: 795-805. Go to original source...
    18. Gardell B. (1982): Scandinavian research on stress in working life. International Journal of Health Services, 12: 31-41. Go to original source... Go to PubMed...
    19. Gellerstedt S. (1997): Mechanised cleaning of young forest - the strain on the operator. International Journal of Industrial Ergonomics, 20: 137-143. Go to original source...
    20. Gellerstedt S. (2002): Operation of the single-grip harvester: motor-sensory and cognitive work. International Journal of Forest Engineering, 13: 35-47. Go to original source...
    21. Gellestedt S., Almqvist R., Myhrman D., Wikstrom B.O., Attebrant M., Winkel J. (1999): Ergonomic Guidelines for Forest Machines Handbook. Uppsala, Swedish National Institute for Working Life, Forestry Research Institute of Sweden, Swedish University of Agricultural Sciences: 85.
    22. Gerasimov Y., Sokolov A. (2009): Ergonomic characterization of harvesting work in Karelia. Croatian Journal of Forest Engineering, 30: 159-170.
    23. Grieco A. (1986): Sitting posturel and old problem and a new one. Ergonomics, 29: 345-362. Go to original source... Go to PubMed...
    24. Griffin M.J. (2006): Vibration and Motion. In: Handbook of Human Factors and Ergonomics. New York, John Wiley & Sons: 590-609. Go to original source...
    25. Hansson J.E. (1990): Ergonomic design of large forestry machines. International Journal of Industrial Ergonomics, 5: 255-266. Go to original source...
    26. Hansson P.A. (1995): Optimization of agricultural tractor cab suspension using the evolution method. Computers and Electronics in Agriculture, 12: 35-49. Go to original source...
    27. Hinz B., Seidel H., Menzel G., Blüthner R. (2002): Effects related to random whole-body vibration and posture on a suspended seatwith and without backrest. Journal of Sound and Vibration, 253: 265-282. Go to original source...
    28. Hnilica R., Dado M., Šoteková A. (2013): Invenzita hluku verzus psychická záťaž človeka. Acta Facultatis Technicae, 18: 43-52.
    29. Hostens I., Ramon H. (2003): Descriptive analysis of combine cabin vibrations and their effect on the human body. Journal of Sound and Vibration, 266: 453-464. Go to original source...
    30. Huang K.D., Tzeng S.C., Jeng T.M., Chiang W.D. (2006): Airconditioning system of an intelligent vehicle-cabin. Applied Energy, 83: 545-557. Go to original source...
    31. Hulstof C., Zanten B.V. (1987): Whole-body vibration and low-back pain. International Archives of Occupational and Environmental Health, 59: 205-220. Go to original source... Go to PubMed...
    32. Huston D.R., Johnson C.C., Wood M.A., Zhao X. (1999): Vibration attenuating characteristics of air filled seat cushions. Journal of Sound and Vibration, 222: 333-340. Go to original source...
    33. Chen J.C., Chang W.R., Shih T.S., Chen C.J., Chang W.P., Dennerlein J.T. (2003): Predictors of whole-body vibration levels among urban taxi drivers. Ergonomics, 46: 1075-1090. Go to original source... Go to PubMed...
    34. Jansen N.W.H., Kant I., Nijhuis F.J.N. Swaen, G.M.H., Kristensen T.S. (2004): Impact of worktime arrangements on work-home interference among duth employees. Scandinavian Journal of Work, Environment and Health, 60: 139-148. Go to original source... Go to PubMed...
    35. Kaynakli O., Kilic M. (2005): Investigation of indoor thermal comfort under transient conditions. Building and Environment, 40: 165-174. Go to original source...
    36. Kim S.C., Won J.P., Kim M.S. (2009): Effects of operating parameters on the performance of a CO2 air conditioning system for vehicles. Applied Thermal Engineering, 29, 2408-2416. Go to original source...
    37. Kolich M., Essenmacher S.D., McEvoy J.T. (2005). Automotive seating: the effect of foam physical properties on occupied vertical vibration transmissibility. Journal of Sound and Vibration, 281: 409-416. Go to original source...
    38. Lewark S. (2005): Scientific Reviews of Ergonomic Situation Mechanized Forest Operations. Uppsala, Sveriges Lantbruksuniversitet: 185
    39. Li L., Lamis F., Wilson S.E. (2008): Whole-body vibration alters proprioception in the trunk. International Journal of Industrial Ergonomics, 38: 792-800. Go to original source...
    40. Magnusson M., Pope M., Rostedt M., Hansson T. (1993). Effect of backrest inclination on the transmission of vertical vibrations through the lumbar spine. Clinical Biomechanics (Bristol, Avon), 8: 5-12. Go to original source... Go to PubMed...
    41. Marsili A., Ragni L., Vassalini G. (1998): Vibration and noise of a tracked forestry vehicle. Journal of Agricultural Engineering Research, 70: 295-306. Go to original source...
    42. Meister W. (1975): Verfahren zur vergleichender Eunschätzun psychologish beanspruchender Tätigkeiten. In: Kongressband 4. Berlin, Gesellschaft für Psychologie: 12
    43. Melnick W. (1991): Hearing Loss from Noise Exposure. In: Handbook of Acoustical Measurements and Noise Control. New York, McGraw-Hill: 18.1-18.19.
    44. Messingerová V., Martinusová L., Slančík M. (2005): Ergonomic parameters of the work of integrated technologies at timber harvesting. Croatian Journal of Forest Engineering, 26: 79-84.
    45. Mezrhab A., Bouzidi M. (2006): Computation of thermal comfort inside a passenger car compartment. Applied Thermal Engineering, 26: 1697-1704. Go to original source...
    46. Mohammadi G. (2008): Hearing conservation programs in selected metal fabrication industries. Applied Acoustics, 69: 287-292. Go to original source...
    47. Nieuwenhuis M., Lyons M. (2002): Health and safety issues and perceptions of forest harvesting contractors in Ireland. International Journal of Forest Engineering, 13: 69-76. Go to original source...
    48. Olesen B.W. (1995): International standards and the ergonomics of the thermal environment. Applied Ergonomics, 26: 193-302. Go to original source... Go to PubMed...
    49. Ovaskainen H. (2009): Timber Harvester Operators' Working Technique in First Thinning and the Importance of Cognitive Abilities on Work Productivity. [PhD Thesis.] Joensuu, University of Joensuu: 62. Go to original source...
    50. Paddan G.S., Griffin M.J. (2002): Effect of seating on exposures to whole-body vibration in vehicles. Journal of Sound and Vibration, 253: 215-241. Go to original source...
    51. Parsons K.C.C. (1995): Ergonomics of the physical environment. Applied Ergonomics, 26: 281-292. Go to original source... Go to PubMed...
    52. Poschen P. (1993): Forestry, a safe and healthy profession? Available at http://www.fao.org/docrep/u8520e/u8520e03.htm
    53. Rottensteiner C., Tsioras P., Neumayer H., Stampfer K. (2013): Vibration and noise assessment of tractor-trailer and truckmounted chippers. Silva Fennica, 47: 14. Go to original source...
    54. Sherwin L.M., Owende P.M.O., Kanali C.L., Lyons J., Ward S.M. (2004a): Influence of forest machine function on operator exposure to whole-body vibration in a cut-to-length timber harvester. Ergonomics, 47: 1145-1159. Go to original source... Go to PubMed...
    55. Sherwin L.M., Owende P.M.O., Kanali C.L., Lyons J., Ward S.M. (2004b): Influence of tyre inflation pressure on wholebody vibrations transmitted to the operator in a cut-tolength timber harvester. Applied Ergonomics, 35: 253-61. Go to original source... Go to PubMed...
    56. Schwartz M., Dado M., Hnilica R. (2013): Rizikové faktory pracovného prostredia. Zvolen, Technická univerzita vo Zvolene: 439.
    57. Sümer S.K., Say S.M., Ege F., Sabanci A. (2006): Noise exposed of the operators of combine harvesters with and without a cab. Applied Ergonomics, 37: 749-756. Go to original source... Go to PubMed...
    58. Tiemessen I.J., Hulshof C.T.J., Frings-Dresen M.H.W. (2007): An overview of strategies to reduce whole-body vibration exposure on drivers: A systematic review. International Journal of Industrial Ergonomics, 37: 245-256. Go to original source...
    59. Tsioras P.A. (2012): Promotion of Safety in Forest Operations. Zilina, EDIS: 1395-1399.
    60. Yamada Y. (1998): Two effective methods for the evaluating mental work load on machine-operators - fractal dimensional analysis with the CGSA method. Journal of Forest Research, 3: 151-154. Go to original source...
    61. Zhang H., Dai L., Xu G., Li Y., Chen W., Tao W.Q. (2009a): Studies of air-flow and temperature fields inside a passenger compartment for improving thermal comfort and saving energy. Part II: Simulation results and discussion. Applied Thermal Engineering, 29: 2028-2036. Go to original source...
    62. Zhang H., Dai L., Xu G., Li Y., Chen W., Tao W.Q. (2009b): Studies of air-flow and temperature fields inside a passenger compartment for improving thermal comfort and saving energy. Part I: Test/numerical model and validation. Applied Thermal Engineering, 29: 2022-2027. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content